|
|
Model HC6502 - 20MHz Dual Trace
Oscilloscope with Alt-Mag .
|
-
20MHz Bandwidth
-
Alt-Mag sweep for simultaneous
display of main and X5 magnified trace
-
1mV/Div Vertical sensitivity
-
Alternate trigger for a stable
display of unrelated signals
-
X5 Sweep Magnification
-
Large 6 inch CRT with internal
graticule, for parallax free measurements
-
Autofocus
-
Internal Sync separator circuit
for stable triggering on video signals
-
Lightweight with low power
consumption
-
Supplied with 2 (X1, X10)
probes and operating manual
|
|
|
| Specification |
| Vertical
Amplifier (CH 1 and CH 2) |
| Sensitivity |
5mV/Div to
5V/Div in 10 steps (1-2-5 seq) X5 Mag: 1mV/Div to 1V/Div |
| Accuracy |
±3% (5% in
X5 Mag) |
| Bandwidth
(-3dB) |
DC to 20MHz |
| Rise
Time |
< 17.5ns |
| Input
Impedance |
1MW + 25pF |
| Input
Coupling |
AC-Gnd-DC |
| Invert
Channel |
CH2 |
| Display
Modes |
CH1, CH2,
Add, Dual |
| Chop
Frequency |
250kHz ±3% |
| Maximum
Input Voltage |
400V (DC
or AC peak) |
| CH1
Signal Output |
20mV/Div
into 50W: (50Hz to 5MHz) |
| Horizontal
Sweep |
| Sweep
Time |
0.1µs/Div
to 0.2s/Div in 20 steps (1-2-5 seq) X5 Mag: 20ns/Div to 40ms/div |
| Accuracy |
±3% (±5%
in X5 Mag) |
| Display
Mode |
A, Alt-Mag,
XY |
| Sweep
Magnifier |
X5 ±5% |
| Trace
Sep |
1.5 Div
Min |
| Horizontal
Amplifier |
| Linearity |
±3% (±5%
in X5 Mag) |
| X-Y
Mode |
CH 1-X axis,
CH 2-Y axis |
| Sensitivity |
Same as
CH 1 Vertical Amplifier |
| Bandwidth
(-3dB) |
DC to 500kHz |
| Phase
Error |
£ 3° DC
to 50kHz |
| Triggering |
| Modes |
Auto, Norm,
TV-V, TV-H |
| Source |
CH 1, CH
2, Line, EXT |
| Coupling |
AC |
| Slope |
Positive
or Negative |
| Trigger
Sensitivity |
- Int: DC to 2MHz: 2 Div
- 2MHz to 20MHz: 3 Div
- Ext: DC to 2MHz: 200mV P-P; 2MHz to 20MHz: 300mV P-P
- TV Synch: Int: 1 Div Min; Ext: 1 V P-P Min
- TV-H (Television Line synchronizing Freq)
- TV-V (Television Frame synchronizing Freq)
- Automatically switched by the A Time/Div Front panel contro
|
| External
Trigger Input |
Input Impedance:
1 MW+ 20pF Maximum Input Volts: 300V (DC or AC peak) |
| Z Axis Modulation |
| Sensitivity |
5V P-P (Intensity
increases with a negative going input) |
| Bandwidth
(-3dB) |
DC to 2MHz |
| Input
Impedance |
Approx.
33 KW |
| Maximum
Input Voltage |
30V (DC
or AC peak) |
| Calibrator
Signal |
| Frequency |
Approx.
1kHz (±20%) |
| Voltage |
0.5V P-P
±3% |
| Duty
Cycle |
Approx.
50% |
|
CRT
|
| Type |
6" rectangular
CRT with illuminated internal 8 X 10 Div graticule (1 Div =
1cm) |
| Acceleration
Voltage |
2kV |
| General
Specification |
| Power
Requirements |
AC Input
Voltage: 100V, 120V, 220V, 240V ±10% selectable |
| Frequency |
50/60Hz |
| Power
Consumption |
35W |
| Operating
Temperature |
0 to 40°C |
| DIMensions |
5.5" H x
13.4" W x 14.8" D |
| Weight |
24 lbs. |
| Supplied
Accessories |
Manual,
AC Power cord, (2) X1/X10 Probes |
|
E-mail us your question
|
 |
|
|
